Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON A RV500W 333 BK - PA66-GF50 - RadiciGroup High Performance Polymers

Check here, which other Radilon A datasheets, application examples or technical articles are available in Material Data Center

Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Fonctions

Any use of this information falls under the rules of our disclaimer.

Informations produit

PA66 50% glass fibre reinforced injection moulding grade. Heat stabilized. Black colour.

Suitable for parts requiring very high stiffness and mechanical resistance, along with excellent heat ageing properties retention.

Caractéristiques des transformations/physiques	sec / cond	Unité	Norme du test
ISO Data
Retrait au moulage, parallèle	0.2 / *	%	ISO 294-4, 2577
Retrait au moulage, perpendiculaire	0.7 / *	%	ISO 294-4, 2577

Propriétés mécaniques	sec / cond	Unité	Norme du test
ISO Data
Module en traction	16300 / 14500	MPa	ISO 527
Contrainte à la rupture	230 / 195	MPa	ISO 527
Déformation à la rupture	2.5 / 3.2	%	ISO 527
Résistance au choc Charpy, +23°C	85 / 105	kJ/m²	ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C	14 / 17	kJ/m²	ISO 179/1eA

Propriétés thermiques	sec / cond	Unité	Norme du test
ISO Data
Température de fusion, 10°C/min	260 / *	°C	ISO 11357-1/-3
Température de fléchissement s/chrg, 1.80 MPa	250 / *	°C	ISO 75-1/-2
Température de fléchissement s/chrg, 8.00 MPa	215 / *	°C	ISO 75-1/-2
Température de ramolliss. Vicat, B	250 / *	°C	ISO 306
Inflammabilité pr. épaisseur h	HB / *	class	IEC 60695-11-10
Epaisseur de l'éprouvette	0.8 / *	mm	-

Propriétés électriques	sec / cond	Unité	Norme du test
ISO Data
Résistivité transversale	1E13 / 1E11	Ohm*m	IEC 62631-3-1
Résistivité superficielle	* / 1E10	Ohm	IEC 62631-3-2

Propriétés diverses	sec / cond	Unité	Norme du test
Absorption d'eau	4 / *	%	Sim. to ISO 62
Absorption d'humidité	1.1 / *	%	Sim. to ISO 62
Masse volumique	1580 / -	kg/m³	ISO 1183

Fonctions

Caractéristiques

Transformation

Moulage par injection

Conditionnement

Grains, Noir

Additifs

Agent de démoulage

Propriétés spéciales

Stabilisé à la chaleur

Disponibilité régionale

Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique

Autres informations

Moulages par injection

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.15%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
280 - 300°C	80 - 100°C	medium-high

Conditions générales

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.